Apps with their own web interface¶
Some apps are configured in their own dashboard, opened in the browser, and not inside LuCI. The
three below are installed with the firmware. The examples assume the router is at 192.168.1.1.
Start and stop an app¶
Every app has an Enable box on its LuCI page (Services → the app's name). Tick it and press Save & Apply to start; untick it and press Save & Apply to stop. One switch, the same everywhere.
Advanced: System → Startup lists services with Start and Stop buttons. They act only for the current session. The Enable box is what decides whether the app runs after a reboot.
Syncthing: folder sync¶
Keeps folders in step between your phone, your PC and a drive on the router.
- Services → Syncthing, tick Enable, Save & Apply.
- Open the dashboard:
http://192.168.1.1:8384. - First thing to do: Actions → Settings → GUI, set a user name and password. Until then anyone on your network can open the dashboard.
- Add your other devices (Add Remote Device) and choose the folders to share.
To keep the dashboard private to the router itself, set the Dashboard address on the LuCI page
to http://127.0.0.1:8384.
AdGuard Home: DNS filtering¶
Blocks ads and trackers for every device and shows what each device looks up.
- Services → AdGuard Home, tick Enable, Save & Apply.
- The first time, the setup wizard is at
http://192.168.1.1:3000. - In the wizard choose a dashboard port other than 80 or 443 (LuCI uses those) and a DNS port other than 53, unless you move the router's own DNS (dnsmasq).
- Finish the wizard and open the dashboard at the address you chose.
Adblock does a similar job. Use one of them, not both.
qBittorrent: download client¶
Downloads to a USB drive attached to the router, controlled from a web page.
- Services → qBittorrent, tick Enable, Save & Apply.
- Open
http://192.168.1.1:8080. - The user is
admin. There is no shared default password: until you set your own, qBittorrent makes a temporary one every time it starts and prints it to the log. Read it withlogread -e qbittorrent(System → Logs). - Set your own: Tools → Options → Web UI → Authentication.
The default download folder is on the USB drive (/mnt); attach and mount it first.
Out of the box¶
| app | state | its own interface | first thing to set |
|---|---|---|---|
| AdGuard Home | off | its own dashboard | it is given a local upstream by 97-cw-adguard-enable-bridge, so the router's own resolution keeps working when the filter starts |
| Syncthing | off | http://0.0.0.0:8384 |
a password. The interface binds all addresses as shipped |
| qBittorrent | off | its own web UI | the download directory. It defaults to the first USB drive |
| Adblock | off | no interface of its own | the checkbox on its LuCI page |
What is listening¶
Nothing until you enable an app. Each one's port and address are in files, ports and paths.
When it does not work¶
| symptom | what it means |
|---|---|
| The whole network stops resolving when AdGuard Home starts | the upstream loop. This image's first-boot script wires the local upstream precisely to prevent it; if the script did not run, check the resolver port it expects |
| Syncthing's page is open to your network | it is: 0.0.0.0:8384. Set a username and password before you enable it |
| Downloads go to flash and fill it | the download directory. Point it at a mounted USB drive first |
An app's page shows nothing after apk upgrade |
the pinned LuCI packages were replaced. See updating and pinning |
Questions people ask¶
Which apps have their own web page on CleanWRT?
AdGuard Home, Syncthing and qBittorrent. Each is installed and switched off, and each listens on its own port only after you enable it.
Does enabling AdGuard Home break the router's own DNS?
Not on this image. A first-boot script gives it the local upstream it needs, which is the usual way this goes wrong on a stock install.